Michele Reynolds
http://inspirationink.typepad.com/inspiration-ink/ michelerey@aol.com |
Still Scenes Deer Snowglobe Joy |
F un, pretty shaker card for the holidays using Stampin' Up! products.
|
|
Cut cardstock, designer paper, and Foil Sheets pieces to the following sizes using a Paper Trimmer:
- card from Seaside Spray Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 3-7/8" x 5-1/8" from Pretty Peacock Cardstock
- 3" square cut from the bottom of the snowy woods design from the Feels Like Frost 6x6" Specialty Designer Series Paper
- 1-1/2" x 3-7/8" of one of the white designs on silver background from the Feels Like Frost 6x6" Specialty Designer Series Paper
- 1-1/2" x 3" from Seaside Spray Cardstock
- 1" x 2" from Whisper White Cardstock
- 1-5/8" x 2-1/8" from Silver Foil Sheets
Adhere the square of Feels Like Frost Specialty Designer Series Paper to the front of the Seaside Spray card so it is about 5/8" from the top, left, and right sides. Make sure the ground is along the bottom of the square.
Pick out the top of the snow globe die from the Snow Globe Scenes Dies. Put it on top of the Pretty Peacock rectangle on a platform on your cutting and embossing tool so it is centered side to side and about 1/2" from the top. Run through the tool.
Tip: You are using the large rectangle of Pretty Peacock with the shape cut out of the top on this project. Throw away the flattened circle cut out or save it to use as scrap on a future project.
Insert the Pretty Peacock rectangle with the shape cut out of it into the Subtle 3D Embossing Folder so the lines run vertically on the vertical rectangle. Place the folder with the paper inside on your die cutting and embossing tool and run through the machine.
Adhere the 1-1/2" x 3-7/8" strip of Feels Like Frost 6" x 6" Specialty Designer Series Paper to the bottom of the cut and dry embossed Pretty Peacock rectangle.
WITHOUT ADHERING, lay the cut and dry embossed Pretty Peacock rectangle on top of the Seaside Spray card so it is centered. Use a pencil to mark the bottom of the cut out on the designer paper square.
Pick out the deer die from the Snow Globe Scenes Dies. Put it on top of the Silver Foil Sheets rectangle on a platform on your cutting and embossing tool. Run through the tool. Use the Take Your Pick Die Brush Tip and paper-piercing tool on the Take Your Pick to remove the pieces.
Use the Fine-Tip Glue Pen or Mulitpurpose Liquid Glue to adhere the silver foil deer cut out to the front of the card so it is centered side to side on top of the Feels Like Frost Designer Paper square and the top of the base of the deer is just above the penciled line you drew.
Rub the inside of a Snow Globe Shaker Dome with the Embossing Buddy to help remove some of the static. Then, wipe out any powder from the Embossing Buddy using a clean, dry paper towel.
Put SNAIL Adhesive on the back of the cut and dry embossed Pretty Peacock rectangle with the designer paper strip attached to the bottom.
Peel the protective backing off the FRONT of the rim around the Snow Globe Shaker Dome. Place the dome on top of a Silicone Craft Sheet so the open area of the dome is on the bottom and the curved dome is on the top. Adhere the Pretty Peacock/designer paper rectangle over the top of the shaker dome.
Tip: Working on top of the Silicone Craft Sheet will keep the adhesives from sticking when you don't want them to stick just yet!
Open the card and lay it flat on your work surface.
Put a pinch of the Snowflake Sequins and the Dazzling Diamonds Stampin' Glitter on top of the deer cut out on the card front.
Peel the protective backing off the BACK of the rim of the Snow Globe Shaker Dome. Adhere the Pretty Peacock/designer paper/shaker dome rectangle to the front of the card so it is centered. Press firmly along the edges of the snow globe to make a tight seal so none of the sequins or glitter can escape.
Mount the snow globe base image from the Still Scenes Set on Block H. Ink it up with the Pretty Peacock Ink Pad. Stamp it in the center of the Seaside Spray rectangle.
Pick out the open snow globe base die from the Snow Globe Scenes Dies. Put it on top of the stamped snow globe base image on a platform on your cutting and embossing tool so the image is centered. Run through the tool.
Mount the "May the timeless message..." sentiment from the Still Scenes Set on Block H. Carefully ink up only the words ""with joy" on the bottom line using the brush tip of the Pretty Peacock Marker. Breathe on the stamp to moisten the ink and stamp it on the small strip of white cardstock so you stamp the inked up words.
Pick out the small, thin tag die from the Ornate Frames Dies. Put it on top of the stamped sentiment on a platform on your cutting and embossing tool so the sentiment is centered up and down and is close to the top of the tag with the top of the tag being on the left side. Run through the tool.
Cut a 2-3/4" piece of Whisper White Solid Baker's Twine.
Thread the tag onto the twine.
Put some SNAIL Adhesive on the back of the tag and adhere it at a slight angle to the right side of the snow globe base cut out.
Wrap the ends of the twine around to the back side of the snow globe base cut out and adhere them in place using small pieces of Tear & Tape Adhesive. Leave the protective backings in place.
Put Stampin' Dimensionals on the back of the snow globe base cut out with twine attached. Remove the protective backings from the Dimensionals and adhere the snow globe base cut out to the front of the card so it butts up to the bottom of the snow globe dome.
Cut an 8" piece of Whisper White Solid Baker's Twine.
Slide one end of the twine under the twine on top of the tag. Tie in place using a small bow. Trim the ends.
Give your card a shake and enjoy!